Member of the Month

profa_212
July, 2025

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Where do I find binding screw lengths?

profile picture
muffMan.
Posts: 2930 - Karma: 28,097
I am looking for a replacement set of screws for some marker barons.


i don’t have a single screw, so can’t measure the original. Also can’t get a response from marker.

Is there a site that lists this info? Ordered a pack of 20 5.5x11.5, yet binding freedom said it might be short.


or if anyone knows which ones to get that would be chilling as well
6 months ago
1 0
profile picture
quagsire
Posts: 280 - Karma: 1,317
Go to a shop, they'll probably have a bin of random screws you can dig through. Ideally you want ~7-8mm of thread portruding into the ski, so find a screw that gives you that and then order that length.
6 months ago
0 0
profile picture
tdollo
Posts: 3885 - Karma: 19,911
Might be wrong but I'm pretty sure the Barons use the same length screws as the heel track base plate for Squire 11, Griffon 13 and Jester 16s. At least that's what i've used previously on Barons that came without any screws.

**This post was edited on Jan 29th 2025 at 5:26:13pm
6 months ago
2 0
profile picture
muffMan.
Posts: 2930 - Karma: 28,097
quagsireGo to a shop, they'll probably have a bin of random screws you can dig through. Ideally you want ~7-8mm of thread portruding into the ski, so find a screw that gives you that and then order that length.


Sounds good! Thanks for the length tip, tried a local shop and couldnt help. “they only have time for paying customers”.

Called an REI near me who might help, but also, it’s REI
6 months ago
1 0
profile picture
muffMan.
Posts: 2930 - Karma: 28,097
tdolloMight be wrong but I'm pretty sure the Barons use the same length screws as the heel track base plate for Squire 11, Griffon 13 and Jester 16s. At least that's what i've used previously on Barons that came without any screws.

**This post was edited on Jan 29th 2025 at 5:26:13pm


Appreciate it! Have been checking dukes, f10s and f12s with no luck. Will try out those too.
6 months ago
1 0
profile picture
deadhead420
Posts: 2168 - Karma: 18,972
where are you located? I’ve got so many marker screws in my spare parts

this post made by marker gang
6 months ago
1 0
profile picture
deadhead420
Posts: 2168 - Karma: 18,972
https://www.bindingfreedom.com/screw-lengths/

you were close

Marker Barron requires 18 10mm flat heads. Should be easy to find those
6 months ago
0 0
profile picture
muffMan.
Posts: 2930 - Karma: 28,097
mrk127https://www.bindingfreedom.com/screw-lengths/

you were close

Marker Barron requires 18 10mm flat heads. Should be easy to find those


So actually ordered based on that, but I guess it is recs for their inserts, not normal alpine screws.

So I am putting these on some predrilled holes, measured the depth and all of them are around 8mm deep, with one being 11mm (the one weird screw in the middle).

plan is to take them off the one that is quiver killed, measure total screw length, measure the bit sticking out of binding, and go from there.
6 months ago
1 0
profile picture
muffMan.
Posts: 2930 - Karma: 28,097

Got these mounted, came out nicely.

For anyone who comes across this, marker barons/duke frame bindings need around 13mm alpine screws, ordered from tognar.

this gave me right around 9mm of thread, I did use a toothpick plus sharpie so not exact, but feels secure. Everything felt real snug, no stripped holes as well.
6 months ago
1 0
All times are Eastern (-4); Currently it's 9:38AM