Member of the Month

Biffbarf
February, 2025

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Look pivot heel arms

profile picture
Koshermilk
Posts: 515 - Karma: 1,913
Just bought new boots, did a pivot adjustment myself (going to bring them into the shop tomorrow after skiing) is this chill? The foward pressure indicator is lined up correctly in the middle of the black markers. Wondering if the heel arms are screwed on too tight or not though? Lmk



Mar 3 2024 9:57PM
3 0
profile picture
scratchskier321
Posts: 2691 - Karma: 868
if you pull the tube back like 20* and it snaps back... ur alright
Mar 4 2024 1:00AM
0 0
profile picture
PartyBullshiit
Posts: 4568 - Karma: 20,417
Are they bottomed out?
Mar 4 2024 1:10AM
1 0
profile picture
Koshermilk
Posts: 515 - Karma: 1,913
PartyBullshiitAre they bottomed out?


Like 2 mm from bottomed out, so no
Mar 4 2024 1:11AM
0 0
profile picture
Koshermilk
Posts: 515 - Karma: 1,913
scratchskier321if you pull the tube back like 20* and it snaps back... ur alright


Wym?
Mar 4 2024 1:11AM
0 0
profile picture
Koshermilk
Posts: 515 - Karma: 1,913
PartyBullshiitAre they bottomed out?


I’m moreso worried if it would damage the heel if my boot or something, like where the heel binding bites into the top part of the heel
Mar 4 2024 1:12AM
0 0
profile picture
Koshermilk
Posts: 515 - Karma: 1,913
PartyBullshiitAre they bottomed out?


Also wondering if the pivot heel screw range is ok if they are screwed this tight
Mar 4 2024 1:15AM
0 0
profile picture
scratchskier321
Posts: 2691 - Karma: 868
KoshermilkWym?


with the boot in the binding, push the dildo down like 20* and let go, it should snap back quickly into place if its correct.
Mar 4 2024 1:31AM
2 0
profile picture
scratchskier321
Posts: 2691 - Karma: 868
and also take your hand a try to move the dildo side to side, it shouldnt move.
Mar 4 2024 1:32AM
0 0
profile picture
Koshermilk
Posts: 515 - Karma: 1,913
scratchskier321with the boot in the binding, push the dildo down like 20* and let go, it should snap back quickly into place if its correct.


Bet yea it doesn’t really snap back into place unfortunately, but it is hard to move the dildo side to side
Mar 4 2024 1:36AM
0 0
profile picture
scratchskier321
Posts: 2691 - Karma: 868
KoshermilkBet yea it doesn’t really snap back into place unfortunately, but it is hard to move the dildo side to side

ok, your wings might be too tight then... back the wings off a little bit until you get a nice dildo snap back move to it.
Mar 4 2024 1:43AM
1 0
profile picture
PartyBullshiit
Posts: 4568 - Karma: 20,417
KoshermilkI’m moreso worried if it would damage the heel if my boot or something, like where the heel binding bites into the top part of the heel

If the dildo isn’t popping right back up into place then the FP is off. Back the arms out a tad and try again. The white tap is typically useless for judging adjustments. It’s not super accurate.



if it’s way too tight you should see a little dent happening pretty quick on the boot
Mar 4 2024 12:41PM
4 0
profile picture
0___
Posts: 3575 - Karma: 15,806
PartyBullshiitIf the dildo isn’t popping right back up into place then the FP is off. Back the arms out a tad and try again. The white tap is typically useless for judging adjustments. It’s not super accurate.



if it’s way too tight you should see a little dent happening pretty quick on the boot


mmmm
Mar 4 2024 8:36PM
1 1
profile picture
Koshermilk
Posts: 515 - Karma: 1,913
Psa: I took them to a shop and rode my old boots today
Mar 4 2024 8:42PM
1 0
profile picture
scratchskier321
Posts: 2691 - Karma: 868
KoshermilkPsa: I took them to a shop and rode my old boots today

im pretty confident if you just backed off the wings a bit, it would be correct.
Mar 4 2024 9:01PM
0 0
profile picture
Koshermilk
Posts: 515 - Karma: 1,913
scratchskier321im pretty confident if you just backed off the wings a bit, it would be correct.


Yea I think so too, but it seems weird to have the arms screwed almost all the way in, when I’ve always seen you are supposed to see at least one set of the perforated part
Mar 4 2024 9:10PM
0 1
profile picture
scratchskier321
Posts: 2691 - Karma: 868
KoshermilkYea I think so too, but it seems weird to have the arms screwed almost all the way in, when I’ve always seen you are supposed to see at least one set of the perforated part


the wings get tighter if the BSL of the boot your using, is shorter than the BSL it was originally mounted for.
Mar 4 2024 11:05PM
0 0
profile picture
Koshermilk
Posts: 515 - Karma: 1,913
scratchskier321the wings get tighter if the BSL of the boot your using, is shorter than the BSL it was originally mounted for.


Yea ik… but I’ve never seen anyone ride pivots with the arms fully screwed in
Mar 4 2024 11:10PM
0 0
profile picture
scratchskier321
Posts: 2691 - Karma: 868
KoshermilkYea ik… but I’ve never seen anyone ride pivots with the arms fully screwed in


if your not gonna go ahead and fix it, im done commenting. good luck sir
Mar 4 2024 11:35PM
0 1
profile picture
Koshermilk
Posts: 515 - Karma: 1,913
scratchskier321if your not gonna go ahead and fix it, im done commenting. good luck sir


Lol I already brought these to a shop, said that in an earlier comment
Mar 5 2024 12:21AM
0 0
profile picture
scratchskier321
Posts: 2691 - Karma: 868
KoshermilkLol I already brought these to a shop, said that in an earlier comment


in theory, people who works in shops should know how bindings work. but they usually dont. *shrug*
Mar 5 2024 12:54AM
0 2
profile picture
PartyBullshiit
Posts: 4568 - Karma: 20,417
KoshermilkYea ik… but I’ve never seen anyone ride pivots with the arms fully screwed in


People ride them both at the bottom and the top. You usually see the middle because that’s normally where it’s set when they get mounted in the middle of the adjustment range so you can go up or down if needed. If you then go to a smaller bsl you have to go down on the arms. Or longer if you get to a larger bsl.
Mar 5 2024 10:16AM
3 0
All times are Eastern (-4)