Member of the Month

GayWolf420
June, 2025

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Look Pivot 15 Toe Piece Side to Side Play

profile picture
Getshifty
Posts: 363 - Karma: 2,231
Hey guys, I've got a pair of Look Pivot 15s that have about 170-200 days on them. I noticed that the toe piece has side to side play, it happens when my boot it clicked in as well as when I move it with my hand. Forward pressure is set correctly, tried turning up the DIN on the toe piece and it didn't make a difference. Video for reference, black ones are brand new, just showing how they normally should be. Are they just clapped out? I don't notice it much when I'm riding, are they still safe and is there anything I can do to fix it? Thanks.
https://www.newschoolers.com/videos/watch/1087507/IMG-2814-mov
a year ago
4 0
profile picture
Juviticus
Posts: 465 - Karma: 2,306
Idk best guess is that the metal tower that holds the bearing is worn down on the top and is no longer a square shape. Either that or the internal surfaces on the aluminum toepiece where the tower inserts have worn down. Is it safe? Probably not. Is it clapped? I'd say so. But I've seen people with sketchier pivots than that so do what you want imo

**This post was edited on Feb 19th 2024 at 10:14:53pm
a year ago
5 0
profile picture
BallClapper
Posts: 3725 - Karma: 16,891
That boi be clapped.
a year ago
2 1
profile picture
turntable
Posts: 2742 - Karma: 872
good question. they are designed to have that tilt to them so dont stress.... but that old pair is a little strange
a year ago
0 0
profile picture
turntable
Posts: 2742 - Karma: 872
is the din on the new henrik toe higher than the old one?
a year ago
0 0
profile picture
Getshifty
Posts: 363 - Karma: 2,231
scratchskier321is the din on the new henrik toe higher than the old one?


No they aren’t, I think they are just worn hella. I’ve tried playing with forward pressure / toe din but it doesn’t make a difference. I’m just gonna keep skiing them I don’t really notice it when I’m riding.
a year ago
1 0
profile picture
turntable
Posts: 2742 - Karma: 872
GetshiftyNo they aren’t, I think they are just worn hella. I’ve tried playing with forward pressure / toe din but it doesn’t make a difference. I’m just gonna keep skiing them I don’t really notice it when I’m riding.

theoretically if you landed on a hard surface at an angle, it would have increase chance of toe lung sliding out, as well if you were holding a high angle and hit a bump
a year ago
1 0
profile picture
turntable
Posts: 2742 - Karma: 872
its interesting that the plastic housing is coming up too, in your video. you see the seam of the clear plastic come up?
a year ago
1 0
profile picture
Getshifty
Posts: 363 - Karma: 2,231
scratchskier321its interesting that the plastic housing is coming up too, in your video. you see the seam of the clear plastic come up?


Oh that's just because the plastic cover for the din markings is a bit loose so my hand is pushing on it and lifting it up.
a year ago
0 0
profile picture
Getshifty
Posts: 363 - Karma: 2,231
scratchskier321theoretically if you landed on a hard surface at an angle, it would have increase chance of toe lung sliding out, as well if you were holding a high angle and hit a bump


That makes sense, I haven't had a problem with them pre releasing so not too worried about that. One side effect of that toe piece play could be increased torque on the heel piece. Which I think caused this heel piece metal ring part in the picture below to snap. I've had this happen twice so far, and the only extra parts I have are all already cracked where it snapped lol so these bindings will have to be reduced to park beaters I guess. Gonna try something other than pivots when I buy my next bindings

a year ago
0 0
profile picture
mikem
Posts: 968 - Karma: 9,915
The mount plate is not flush on the ski, the mount screws have worn loose/the plate and it has sway?

It really won't matter at all, if you blow your knee over 2mm of movement due to the age of a binding thats a skill issue.

DON'T crank you dins because of this, if you do anything do the opposite, remember the binding has to give before the stressors in your knee engage. because the binding is loose.

To fix it, buy a baseplate if thats an issue, but also dont care, no binding will lay flat ever.
a year ago
1 0
All times are Eastern (-4); Currently it's 1:59PM