Member of the Month

BradFiAusNzCoCa
October, 2022

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Quick help, pivot screw broke in half

profile picture
sullivanob
Posts: 1225 - Karma: 7,938







how do i fix this and is it a big deal. i can grab another one of those screws from a different set of pivots but how do i get it out?
Nov 11 2021 7:06PM 5 0
profile picture
sullivanob
Posts: 1225 - Karma: 7,938
my bad meant to put this in gear talk
Nov 11 2021 7:12PM 4 0
profile picture
_IRRELEVANT_
Posts: 944 - Karma: 4,403
Nov 11 2021 7:15PM 8 0
profile picture
ASSholebomber22
Posts: 5313 - Karma: 56,873
Can you grab and turn it with pliers? If not you can slot it with a dremel and a cutoff wheel and maybe get it with a flathead. Last resort you'll have to drill it out
Nov 11 2021 7:20PM 4 0
profile picture
RAcecARman
Posts: 184 - Karma: 1,698
Go to a really shitty ski shop that has done you wrong in the past and stealthy steal the floor models screw. Or the hardware store.
Nov 11 2021 7:30PM 7 0
profile picture
sullivanob
Posts: 1225 - Karma: 7,938
RAcecARmanGo to a really shitty ski shop that has done you wrong in the past and stealthy steal the floor models screw. Or the hardware store.


i dont need a new screw, i just need to know if i can ski without the screw and if not how to get out the half screw
Nov 11 2021 7:31PM 1 0
profile picture
RAcecARman
Posts: 184 - Karma: 1,698
sullivanobrien_i dont need a new screw, i just need to know if i can ski without the screw and if not how to get out the half screw


It was a joke. If you can't do it with pliers I'd epoxy that whole piece down so water doesn't get in
Nov 11 2021 7:42PM 1 0
profile picture
weatcoast
Posts: 4715 - Karma: 47,744
This is why I don’t buy Gripwalk or WTR toepieces anymore.


You’ll be fine just epoxy it in or something my WTR toepieces used to do that all the time and I never had issues
Nov 11 2021 7:46PM 3 3
profile picture
AlexHallsEyebrow
Posts: 789 - Karma: 7,404
Side note can you show us the jet-edollos
Nov 11 2021 8:50PM 4 0
profile picture
CatdickBojangles
Posts: 5863 - Karma: 58,703
BiffbarfCan you grab and turn it with pliers? If not you can slot it with a dremel and a cutoff wheel and maybe get it with a flathead. Last resort you'll have to drill it out


That one is gunna be a bitch to get out.
Nov 11 2021 9:23PM 1 0
profile picture
CaIeb
Posts: 316 - Karma: 2,455
idk maybe use some sort of metal rod that will fit in the spot, and then put some super glue in between the two, so it’s almost like an extension of the screw. then just twist it out
Nov 11 2021 9:54PM 2 0
profile picture
Quaggy
Posts: 866 - Karma: 13,036
OP, I was in the same boat as you, but I didn't realize until my entire plastic window fell off.

They make "Left handed drill bits" for this exact purpose. Depending on how hard the metal of the bolt is, you should be able to extract it no problem with a set of lefty bits
Nov 12 2021 2:01AM 3 0
All times are Eastern (-5)