Member of the Month

Farmville420
November, 2022

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

How do I detune my skis

profile picture
gorbdawggybrent
Posts: 970 - Karma: 8,726
I just got my color change wets fellas and I need to get them ready
how do I go about detuning them underfoot without messing them up or taking too much off the edges
I have a metal file and that's it do I need to get more stuff or am I chilling
Nov 7 2021 2:05AM 10 0
profile picture
migidimigi
Posts: 189 - Karma: 1,471
File is more than enough, if you want you can also use gummy stone after filing but no need. My advice is that you shoul try to make the edge round so change the angle of the file quite a lot while grinding the edge.

All in all, you're trying to take the sharpest edge off and your edges will get fucked when hitting rails so don't sweat it, you can't really fuck up too bad
Nov 7 2021 3:13AM 6 0
profile picture
Turd__Authority
Posts: 8401 - Karma: 54,137
Could always use a stone rather than a file. Not a gummy stone but I can't think of the name. It's a tan hard rectangular stone (polishing stone?). That way you can take less off if you're worried about overdoing it. That's what I've used in the past.
Nov 7 2021 8:49AM 4 0
profile picture
Tucko
Posts: 165 - Karma: 1,464
gorbdawggybrentI just got my color change wets fellas and I need to get them ready
how do I go about detuning them underfoot without messing them up or taking too much off the edges
I have a metal file and that's it do I need to get more stuff or am I chilling


Anything rough can technically do it, I’ve even just used a fairly low grit sandpaper. Send pics of the skis!
Nov 7 2021 9:47AM 2 0
profile picture
ButteryStix69
Posts: 363 - Karma: 661
post picks of them pls
Nov 7 2021 12:18PM 2 0
profile picture
gorbdawggybrent
Posts: 970 - Karma: 8,726
TuckoAnything rough can technically do it, I’ve even just used a fairly low grit sandpaper. Send pics of the skis!


ButteryStix69post picks of them pls





The green pivots suit them nicely eh?
Nov 7 2021 1:48PM 17 0
profile picture
gorbdawggybrent
Posts: 970 - Karma: 8,726


I rubbed an ice cube on them
Nov 7 2021 1:51PM 10 0
profile picture
KilaTsunami
Posts: 1539 - Karma: 12,688
Personally, the idea of taking a heavy file to my brand new (very rare, and very sexy) V‘s all on my own makes my stomach turn, but I could just be over protective/under educated about detuning your own edges…

I’d drop them at a ski shop and tell them exactly what you’re looking for. I do it almost every year for my skis and it hasn’t done me wrong yet.
Nov 8 2021 5:56AM 5 2
profile picture
switchlip2
Posts: 1417 - Karma: 17,977
https://youtu.be/CL4FIR2lmKo
Nov 8 2021 8:01AM 1 0
profile picture
Turd__Authority
Posts: 8401 - Karma: 54,137
gorbdawggybrent


I rubbed an ice cube on them

They change colors!?!
Nov 8 2021 8:40AM 4 0
profile picture
ButteryStix69
Posts: 363 - Karma: 661
those are so beutifal
Nov 8 2021 10:06AM 4 0
profile picture
tri_photo
Posts: 1460 - Karma: 6,494
dude those skis are gorgeous
Nov 8 2021 10:40AM 2 0
profile picture
rojo.grande
Posts: 1112 - Karma: 7,837
heavily round off edges under foot and a few inches into the toe and heel pieces of the bindings, then lighter detune running from binding to a few inches forward. Finish lighter tune with a gummy stone. They should be most dull under foot and progressively sharper up and back on the ski. Be sure to also detune tips and catching points where taper starts to avoid hooking on butters.
Nov 8 2021 1:19PM 1 0
profile picture
gorbdawggybrent
Posts: 970 - Karma: 8,726
I just did 60grit sandpaper underfoot cause my metal file sucks apparently
it’s a pretty light detune but I think that’s how I want it to keep the edges as thick as I can
Nov 9 2021 12:20PM 0 0
profile picture
Session
Posts: 5167 - Karma: 19,640
KilaTsunamiPersonally, the idea of taking a heavy file to my brand new (very rare, and very sexy) V‘s all on my own makes my stomach turn, but I could just be over protective/under educated about detuning your own edges…

I’d drop them at a ski shop and tell them exactly what you’re looking for. I do it almost every year for my skis and it hasn’t done me wrong yet.


It never bother me to take a bastard file and a gummy stone to the rocker section of my brand new ON3P's.
Nov 9 2021 12:26PM 1 0
profile picture
KilaTsunami
Posts: 1539 - Karma: 12,688
SessionIt never bother me to take a bastard file and a gummy stone to the rocker section of my brand new ON3P's.


If anything fucked them up I’d never forgive myself
Nov 9 2021 9:13PM 0 0
All times are Eastern (-5)