Member of the Month

profa_212
July, 2025

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Fixing edge breaks (edge coming out)

profile picture
Diento
Posts: 194 - Karma: 619
Dear NS

I bought some second hand On3p kartels 98.
After about 5-6months of riding them in the nearby dome i got quite a few edge cracks and eventually the edge started coming out (see pic) now ive tried repairing it with multiple 2 component epoxys and clamping it in a bench to keep the edge in and using glue clamps to apply pressure from the top/bottom. I've done this 3 times already but the edge will come out again after about a week.... Anyone got any other fixes/suggestions?
5 years ago
3 0
profile picture
theabortionator
Posts: 52783 - Karma: 175,263
I welded my edge together 13/14. Not by the book and probably bad for multiple reasons but it worked and got me to the end of the Northern season. I might have slightly lit my base on fire but too and stuff
5 years ago
4 0
profile picture
f100prerunner
Posts: 504 - Karma: 1,313
Cut off the edge the closest to where it isn’t coming out as possible and epoxy that whole section...maybe even prying up the base in that area where there is no edge and load it up with some waterproof epoxy.
5 years ago
9 0
profile picture
lil.Boye
Posts: 2801 - Karma: 12,726
Either some good epoxy and clanps, or just cut it off
5 years ago
2 0
profile picture
weastcoat
Posts: 6510 - Karma: 75,508
Cut it out where the edge stops bending out, set your skis sideways, put some tape on the base, and put some epoxy in it so the epoxy seeps down into the crack. Works like a charm.


here is the absolute best epoxy for ski repairs. Works insanely well.

https://www.walmart.com/ip/West-Systems-G-FLEX-EPOXY-BOTTLES-2-PKG-650-8/33278209
5 years ago
5 0
profile picture
anders_a
Posts: 1680 - Karma: 5,605
Anyone tried TIG welding edges back together? a small hit should not torch of the base to bad.
5 years ago
3 0
profile picture
Diento
Posts: 194 - Karma: 619
f100prerunnerCut off the edge the closest to where it isn’t coming out as possible and epoxy that whole section...maybe even prying up the base in that area where there is no edge and load it up with some waterproof epoxy.


Alright sounds good :) ill give that a try tomorrow!
5 years ago
3 0
profile picture
PeeDuBzz
Posts: 1010 - Karma: 134
Just cut er out or snap it, should be pretty easy. Snap it upward so there's nothing digging and file down any sharp spots. I'm all for epoxy and there's probably some value in filling the crack as much as possible. However, that works best in the tip and tail IMO. Underfoot will still crack the epoxy and there won't be much left after a rail session. Should still last plenty long if you're only ripping park and don't hit too many icy days.
5 years ago
0 0
profile picture
NattyNine
Posts: 281 - Karma: 1,600
get new skis and put em on the wall.
5 years ago
0 3
profile picture
SoVT
Posts: 118 - Karma: -13
Go look on TGR if you want to learn. There was a guy like a month ago on the gear forum that shows a killer step by step on how to do it. His edge was compressed and broken and he hammers everything out, replaced the section of edge and base.
5 years ago
0 0
profile picture
abar.
Posts: 1062 - Karma: 6,905
If it's bent out that bad you'll need to cut it out, don't try and save more edge than you can, make sure you get it all or it will just pull out farther. Use a hair dryer on the epoxy to push it deeper into the core, it will bind better. If you have an edge starting to pull out, epoxy/hair dry/clamp way earlier when there's less than an mm gap. Use g flex 650 if you can, it's what on3p uses in the factory, make sure it's water proof and has really high tensile strength.
5 years ago
0 0
profile picture
Diento
Posts: 194 - Karma: 619
Thnx for all the tips guys ill try repairing it again otherwise just cut the edge and fill the gap and see what works best
5 years ago
0 0
profile picture
MoneyMakerMike
Posts: 1254 - Karma: 5,764
anders_aAnyone tried TIG welding edges back together? a small hit should not torch of the base to bad.

It could probably be done, but not many ski bums own a tig welder I would assume

**This post was edited on Mar 7th 2020 at 12:31:31am
5 years ago
0 0
profile picture
dolanslebensraum
Posts: 5959 - Karma: -13,093
Imagine having to ski rails until your edges blow, because you were too afraid to hit jumps
5 years ago
0 6
profile picture
f100prerunner
Posts: 504 - Karma: 1,313
anders_aAnyone tried TIG welding edges back together? a small hit should not torch of the base to bad.

I feel like it would definitely ruin the ski base atleast a bit, welding creates insane heat even with only with a zap I’d imagine

**This post was edited on Mar 7th 2020 at 1:54:45am
5 years ago
0 0
profile picture
anders_a
Posts: 1680 - Karma: 5,605
thin sharp tig will let you isolate heat, I will try it out, just gotto kill some edges enough eh
5 years ago
2 0
profile picture
SkierPT
Posts: 2210 - Karma: 4,932
Following. Similar issue
5 years ago
0 0
All times are Eastern (-4); Currently it's 11:08PM