Member of the Month

GayWolf420
June, 2025

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Mounting bindings at home

profile picture
weastcoat
Posts: 6508 - Karma: 75,460
Have any of you done this? I was thinking about doing this. The closest place that mounts is a shop at Seven springs. They charge 90 bucks to mount (just drilling holes and then screwing in a couple screws, yes, for 90 bucks).Is it safe to do? Would I have any issues in the future if I did it by myself? Drop your thoughts below.
9 years ago
1 0
profile picture
Nickyduece
Posts: 26 - Karma: 115
try to find a templet online of your binding and make sure they line up, use the template to drill thru the ski. its very doable if your willing to risk it, but i think you'll be ight. best of luck my dude
9 years ago
0 0
profile picture
weastcoat
Posts: 6508 - Karma: 75,460
NickSodltry to find a templet online of your binding and make sure they line up, use the template to drill thru the ski. its very doable if your willing to risk it, but i think you'll be ight. best of luck my dude

Thanks. I might use a 2 by 4 to make sure I'm drilling straight down
9 years ago
0 0
profile picture
HaydenWrong
Posts: 986 - Karma: 2,165
take your time deff not rocket science just also make sure your heel piece is in the center of it adjustment range... that way if youre a little off either way you can adjust accordingly.. also either buy a drill bit that will only drill as deep as you need or put electrical tape as a depth stopper.. elmers wood glue a dot in each hole good luck
9 years ago
0 0
profile picture
EriksCertified
Posts: 23 - Karma: 61
I would suggest practicing on an old pair of skis.
9 years ago
0 0
profile picture
oxiclean
Posts: 615 - Karma: 693
I did it with no problems.
9 years ago
0 0
profile picture
clorox
Posts: 1728 - Karma: 4,867
HaydenWrongtake your time deff not rocket science just also make sure your heel piece is in the center of it adjustment range... that way if youre a little off either way you can adjust accordingly.. also either buy a drill bit that will only drill as deep as you need or put electrical tape as a depth stopper.. elmers wood glue a dot in each hole good luck


Woodglue is ideal
9 years ago
0 0
profile picture
TDD536
Posts: 160 - Karma: 147
Measure twice, drill once. Use wood glue as lock-tite on the screws, and mark your bit for how deep you want to drill by comparing to the screw. Make sure to not over torque your screws and strip it, start with a drill then finish with hand tighten if your lazy (like me).
9 years ago
0 0
profile picture
gnar_whal
Posts: 1286 - Karma: 3,788
measure once drill as many times as necessary
9 years ago
0 0
profile picture
SammyDubz
Posts: 2168 - Karma: 7,226
Don't measure at all just drill that fucker wherever you think is necessary
9 years ago
1 0
profile picture
p.lochner
Posts: 66 - Karma: 67
Just mounted a pair at home last night. Its not to hard as long as you have some idea of what you're doing.
9 years ago
0 0
profile picture
BedBugDoug
Posts: 590 - Karma: 2,256
I mounted my skis last season primarily by eyeballing them. I would not recommend just eyeballing because they aren't perfectly even (big surprise), but it was easy and I am still skiing them today.
9 years ago
0 0
profile picture
spat_man
Posts: 15 - Karma: 34
Could be pretty risky... If you mess up, their goes your 700 dollar ski. I would pay someone else to do it. Unless you know what your doing and have been practicing on older skis.
9 years ago
0 0
All times are Eastern (-4); Currently it's 1:28PM