Member of the Month

JalmarKalmar
April, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Too much ptex?

profile picture
p00paloop
Posts: 143 - Karma: 12
is it possible to use too much ptex on your bases, i have a pair of beaters and im am just considering dripping that shiz all over them, like an entire new bases of just ptex, do you think it would work, i dont care about how fast they will slide now, i just want them for some urban missions 
Oct 1 2006 5:04PM
0 0
profile picture
KeegLove
Posts: 10166 - Karma: 55
why in gods name would you p-tex them if you are using them for urban, just use them as is.
Oct 1 2006 5:05PM
0 0
profile picture
p00paloop
Posts: 143 - Karma: 12
just answer the god damn question u bitches
Oct 1 2006 5:08PM
0 0
profile picture
liukangkid
Posts: 3323 - Karma: 82
you cant make a totaly new base out of p tex so expensive and wont work
Oct 1 2006 5:15PM
0 0
profile picture
p00paloop
Posts: 143 - Karma: 12
how would that be expensive ptex candles are like 95 cents it would take lke 10 maybe 15 at the most
Oct 1 2006 5:18PM
0 0
profile picture
psychkub
Posts: 1788 - Karma: 16
you probably could. You would need to get a stone ground to even out the bases.... then again it's for urban. I don't see why not.
Oct 1 2006 5:21PM
0 0
profile picture
Smed193
Posts: 188 - Karma: 10
Yea would work
if you covered teh base and then got it stone ground it would accomplish nothing but filling in the scratches and gauges
Oct 1 2006 5:34PM
0 0
profile picture
wazzucrewskier
Posts: 2269 - Karma: 151
just fill in the big shit with p tex.  if you are going to p tex and then stonegrind which is normally like 40 bucks then that is a really stupid idea for urban skis that are just going to get fucked the first time you use them.
Oct 1 2006 5:36PM
0 0
profile picture
C-Burg
Posts: 4729 - Karma: 130
he did answer the question
Oct 1 2006 5:46PM
0 0
profile picture
icecoastn
Posts: 524 - Karma: 15
you cant just put ptex on skis either, the gouges have to have sharp edges, not slowly tapering cuts. so if its a shallow wide and mellow gouge, you cant ptex it because it wont stick.
Oct 1 2006 5:53PM
0 0
profile picture
CTD
Posts: 6300 - Karma: 348
um. bad idea. its SUPER tough to scrape all the PTEX down, and most places are gonna look at your hack ass job, and charge you extra labor charges for scrapping it all down. if your using them for urbans, why the fuck would you bother? if they are horribly slow, hit them in 1 direction with a fine grit belt sander a couple times, or take a hard sharp scraper and cut all the flak off so theres nothing stickin out to drag in the snow. thenmaybe do a quickt wax job of real cheap wax.
Oct 1 2006 6:46PM
0 0
profile picture
stevel
Posts: 1302 - Karma: 19
just take all the p-tex ur going to use to make ur new basses and eat it
Oct 1 2006 7:03PM
0 0
All times are Eastern (-4)