Member of the Month

partyandBS
December, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Adjusting Pivots for New Boots

profile picture
W1lki3
Posts: 7 - Karma: 26
Hi all. Recently upgraded boots, going from some older Tom Wallisch pros to some Dalbello Il Moros. BSL was one mm more on the il moros so figured it wouldn’t be an issue to adjust, but I have loosened the pivot heel piece from the end of the first grooved ring to the end of the third grooved ring and the boots still won’t fit (both are size 28.5 if that helps). Has anyone else had this issue / do I need to remount? Thanks in advance.
Dec 26 2023 10:32PM
4 0
profile picture
switchlip2
Posts: 2142 - Karma: 25,121
Give the break arm dial literally a single turn with a flathead
Dec 26 2023 10:35PM
2 0
profile picture
W1lki3
Posts: 7 - Karma: 26
I did yah (I probably have them about 8 full rotations before they started to be able to get in) but I guess what I’m saying more so is, how far back would be too far back. After letting It sit with the break arm dial unscrewed it looks like there is some grease leaking
switchlip2Give the break arm dial literally a single turn with a flathead



Dec 26 2023 10:56PM
0 0
profile picture
Vish-shoe
Posts: 1949 - Karma: 14,521
You gotta adjust the foreword pressure, google can tell you how to do that
Dec 26 2023 11:03PM
0 9
profile picture
Vish-shoe
Posts: 1949 - Karma: 14,521
https://theskimonster.com/blog/posts/how-to-adjust-your-rossignol-ski-bindings/
Dec 26 2023 11:05PM
7 0
profile picture
Oetk
Posts: 107 - Karma: 210
You shouldn't have to adjust from the 1st to 3rd ring if the soles are only 1mm different. You should barely need to do any adjustments, if at all. Something isn't making sense if you're adjusting that much, 1st to 3rd ring is probably 10mm. Both DIN soles with DIN afds?
Dec 27 2023 10:05AM
7 0
profile picture
tdollo
Posts: 3811 - Karma: 18,956
OetkYou shouldn't have to adjust from the 1st to 3rd ring if the soles are only 1mm different. You should barely need to do any adjustments, if at all. Something isn't making sense if you're adjusting that much, 1st to 3rd ring is probably 10mm. Both DIN soles with DIN afds?


my thoughts exactly, I bet them jawns running loose as a goose
Dec 27 2023 10:11AM
4 0
profile picture
switchlip2
Posts: 2142 - Karma: 25,121
OetkYou shouldn't have to adjust from the 1st to 3rd ring if the soles are only 1mm different. You should barely need to do any adjustments, if at all. Something isn't making sense if you're adjusting that much, 1st to 3rd ring is probably 10mm. Both DIN soles with DIN afds?


Yeah I’m surprised OP had to adjust my new shells went from 295 to 294 and it’s just the same I didn’t need to do any turns
Dec 27 2023 10:23AM
1 0
profile picture
Non_State_Actor
Posts: 4916 - Karma: 17,541
The BSL stamped on the heel may or may not have any relation to the actual length of the boot. Double check that shit.
Dec 27 2023 9:06PM
3 1
profile picture
maaattt
Posts: 2566 - Karma: 31,189
Non_State_ActorThe BSL stamped on the heel may or may not have any relation to the actual length of the boot. Double check that shit.


Most likely answer, if it was truly 1mil difference as listed on the heels you would never need to back that far off
Dec 29 2023 1:46AM
3 0
All times are Eastern (-5)