Member of the Month

GayWolf420
June, 2025

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

So i do a broken grind

profile picture
HARDSTYLE2767
Posts: 595 - Karma: 19

the second day on my trouble makers and this happens

Click for larger image

i talked to dynastar and they say i can warranty.

18 years ago
0 0
profile picture
titsLOL
Posts: 7485 - Karma: 396
duhh that means you did it right, why did you think it was called a broken grind?
18 years ago
0 0
profile picture
*FREEDOM*
Posts: 51 - Karma: 10
you must have rubber knees
18 years ago
0 0
profile picture
=FLO=
Posts: 1969 - Karma: 39
I seriously doubt they will warranty that - sorry
18 years ago
0 0
profile picture
HARDSTYLE2767
Posts: 595 - Karma: 19

mannn

my dads freind is on ski patrol and he did take a knife and cut off the base layer that was jutting upwards.  It made a huge difference i really have no problem skiing them.  i dont know any suggestions you guys have for me trying to fix them on my own

18 years ago
0 0
profile picture
yelsel
Posts: 12967 - Karma: 3,451
ptex will be your bestest friend
18 years ago
0 0
profile picture
spliff.Life
Posts: 7848 - Karma: 1,545
that suckss
18 years ago
0 0
profile picture
-Nick-
Posts: 1479 - Karma: 24
hahaha true
18 years ago
0 0
profile picture
JFerg
Posts: 2440 - Karma: 62
If you cant warranty it, get in there and get dirty. Use pliers to pull the edges to where they are supposed to be and hammer that shit down. Cover it in petex and let it set for a day in the cold, scrape the petex so it's even with your base and it should be good.
18 years ago
0 0
profile picture
HARDSTYLE2767
Posts: 595 - Karma: 19

sounds good im not even going to try to warranty because of the "its your fault if its rail damage shit".  I dont think i will ever trust a broken grind again. 

18 years ago
0 0
profile picture
EClay46
Posts: 2499 - Karma: 69
thats not how u fix a broken edge


go to a shop

or

1. get a new piece of edge, and epoxy
2. cut down edge to the proper length.
3. cut base around broken area in a smooth arc around the spot
4. after roughing up thoroughly, mix the epoxy in a cup
5. put some epoxy in the area where base/edge is missing (makes it easier  to place edge in for me)
6. fit new piece of edge in to missing area
7. use tape to block the epoxy from spilling out the side
8. poor epoxy on to fill the hole
9. Let the epoxy set completely
10. use a file to scrape off any excess epoxy.

u are done
18 years ago
0 0
profile picture
KeithB.
Posts: 608 - Karma: 12
Do what this guy said, done.
18 years ago
0 0
profile picture
Barf.
Posts: 1188 - Karma: 123
That sucks, i would take it to a shop and see what they can do first so don't mess up your skis even more.
18 years ago
0 0
profile picture
zerospinskier
Posts: 4867 - Karma: 350
That is why I don't do far-fig-noo-ginz on my skis.
18 years ago
0 0
profile picture
Silence
Posts: 16030 - Karma: 151
You cereal Dynastar said you could warranty that?

Doubtful - hope they do though.
18 years ago
0 0
profile picture
HeathR
Posts: 4362 - Karma: 1,388
that wont last very long if u ride hard every day. But it might hold up for a little while.
18 years ago
0 0
profile picture
EClay46
Posts: 2499 - Karma: 69
neither will any edge repair
18 years ago
0 0
profile picture
HeathR
Posts: 4362 - Karma: 1,388
thats what i ment. I wasent knocking what u were saying. The way u described sounds a little better then what i do anyways.
18 years ago
0 0
profile picture
chickenwang
Posts: 5639 - Karma: 40

zomg you have 1337 postz

18 years ago
0 0
profile picture
VT_scratch
Posts: 8860 - Karma: 6,804
ahhaha. nice post. u make me lol
18 years ago
0 0
profile picture
golf
Posts: 1418 - Karma: 14
Looks like my dynastar that are a year older than those.
18 years ago
0 0
profile picture
ILoveOhio
Posts: 1793 - Karma: 253
ZOMG!!!!!!!!!! Uber 1337 Pwnzers 0n t3h IV35ch00l3I25!!!!!!

JK.
18 years ago
0 0
profile picture
ILoveOhio
Posts: 1793 - Karma: 253
Sorry for the double post.  If the damage is down to the core, that is very bad.  It is called a core shot and if water gets in there you core could get fucked.  Take it to the shop.  I can't see if it's a core shit.
18 years ago
0 0
All times are Eastern (-4); Currently it's 10:18PM