• Forums
  • Gear Talk
  • Mounting the same binding in the same holes that dont have p-tex

Member of the Month

PartyBullshiit
March, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Mounting the same binding in the same holes that dont have p-tex

profile picture
GrahamStokes
Posts: 157 - Karma: 298
last season i broke a ski and took my bindings off, this season i bought a single replacement ski from someone who also broke one and im wondering if i can put that binding back on in the same place with some wood glue, or do you think a shop would be willing to do that?
Nov 7 2012 7:25PM
1 0
profile picture
JsNeagle
Posts: 1399 - Karma: 1,506
As long as you stored the ski indoors (or in a dry location) they'll be fine.  If it's a good shop that knows what they're doing it will come out as good as new.  I do it all the time to my own skis.  Best approach is plenty of wood glue and counter turning the screws until you feel them fall into the original threads.  If you are careless and rethread the holes, there might be issues down the road.
Nov 7 2012 7:29PM
0 0
profile picture
ProperEnglish
Posts: 2 - Karma: 10
Yeah dude it will work fine. Like previous poster said make sure just be careful and make sure u put some PVA in the holes first. I see far too many skis come in through my shop where people have p***d around with their bindings and not resealed the holes. Resulting in a soft mushy core that wont hold a screw.

Nov 7 2012 8:00PM
0 0
profile picture
freeskibum82
Posts: 6355 - Karma: 5,055
you can do that, but i would prefer to plug those and move the binding forward/back a centimeter and drill new holes.
Nov 7 2012 8:39PM
0 0
profile picture
R.Fahey
Posts: 8602 - Karma: 539
yeah, try it.
The only thing that could be bad is if your strip the holes out. So, screw them back in, and if any of the screws just keep turning the hole is stripped. Normally not a big deal, but can for sure let moisture in and/or more likely to pull out (lol).

DON'T OVER TIGHTEN THE SCREWS.
Nov 7 2012 8:43PM
0 0
profile picture
danbrown
Posts: 11932 - Karma: 21,775
put a bit of elmers glue in the holes before you screw it in so it'll seal them from water
Nov 7 2012 8:52PM
0 0
profile picture
chiefbroseph
Posts: 720 - Karma: 522
you could always use heli-coils which are an "interface" between the ski itself and the screws of the binding. i can't imbed so google em...
Nov 7 2012 9:19PM
0 0
profile picture
freeskibum82
Posts: 6355 - Karma: 5,055
better off drilling new holes than using helis, i know they can work but i pretty much refuse to use them unless i really need to.
Nov 7 2012 10:00PM
0 0
profile picture
GrahamStokes
Posts: 157 - Karma: 298
well the reason i dont want to re drill is cause i dont want my elizabeths anything but center mount, and theyve been mounted twice so i just want to put it back on, but im definitly going to have my shop do it i aint gonna fuck it up
Nov 8 2012 11:18AM
0 0
profile picture
Huck_Norris
Posts: 11487 - Karma: 18,627

quiverkill them shits. 

Nov 8 2012 1:00PM
0 0
profile picture
NinetyFour
Posts: 8650 - Karma: 13,409
Came here to post this. Just size the holes up, put inserts in place, and then you're good to go (well not that easy but you get the idea) or heli-coil the old holes.
Nov 8 2012 1:25PM
0 0
All times are Eastern (-4)